4U 上架式/塔式机箱 支持EATX/ATX 主板 支持 8 SAS/SATA 硬盘 冗余电源 HPC-7442 Sales Kit 4U 上架式/塔式机箱 支持EATX/ATX 主板 支持 8 SAS/SATA 硬盘 冗余电源

目录 关键卖点 规格表 机构亮点 目标应用 订购信息 上架式机箱Roadmap Backup IBM Confidential

关键卖点 High Performance Intelligent 4U 上架式/台式机箱，支持EATX/ATX 母板 抗震硬盘托架设计，4* 移动 3.5” and 2.5” SAS/SATA硬盘支架，支持 RAID 5/10, 超薄光驱, 支持2 * 2.5” 内部设备 可选硬盘升级套件, 支持8块硬盘，提升存储空间 支持 80plus 单电源和冗余电源 Intelligent 较开顶盖式系统风扇，前置式系统风扇更易维护 系统检测故障，LED指示灯和声音报警通知，包括电源，风扇，温度，硬盘，网络 系统风扇智能转速控制 远程管控(协同新的报警板+ SUSIAccess)

规格书 项目 描述 规格 4U 上架式/塔式机箱，支持EATX/ATX 主板 存储空间 4* or 8*(after adding “storage upgrade kit”) mobile trays for 3.5” and 2.5” SAS/SATA HDDs 1* 内部 3.5” 设备 1* 超薄光驱 系统检测 power, HDD, temp, fan, LAN 故障报警和LED指示灯 系统风扇 12cm (front) and 1* or 2*(增加“存储升级套件”) 8cm (storage) cooling fans with reusable air filter I/O 接口 前面: 双USB 口. 后面: five pre-punched 9-pin D-SUB and one 68-pin SCSI openings Switch & 按钮 Power switch, system reset, alarm reset, one-button recovery buttons 电源 80Plus (Bronze and above) PS/2 single and redundant PSU up to 700W 尺寸(W x H x D) 482 x 177 x 600mm (19” x 7” x 23.6”) 环境 Operating Non-Operating 温度 0 ~ 40℃ (32 ~ 104℉) -40 ~ 70 ℃ (-40 ~ 158℉) 湿度 10 ~ 95% @40℃, non-condensing 10 ~ 95% @60℃, non-condensing 振动 (5-500 Hz) 1Grms 2G 冲击 10G (with 11ms duration, half sine wave) 30G

机构亮点 (1/4) Front view (Closed front door) Rear view Front view Lockable front door prevents unauthorized access LED indicators Switch/buttons Slim optical drive bay USB x2 Rear view Front view (Open front door) Thumb screws Front-accessible fan without opening top cover Mobile HDD tray x4 Single and redundant PSU supported Reserved for “storage upgrade kit” to support 4 more mobile HDD trays

机构亮点(2/4) Top view Hold-down clamp with rubber cushions Supports EATX/ATX form factor motherboard 2nd storage fan if installing optional “storage upgrade kit” New alarm board featuring system fan speed control Easy-to-maintain storage fan kit with thumb screw Internal 3.5” drive bay Case open switch *Note: Motherboard and power supply are not included.

机构亮点(3/4) HPC-7442 8-bay sku HPC-7442 default sku Storage upgrade kit (supports 4 mobile HDD trays) Storage upgrade kit (optional) HPC-7442 8-bay sku (supports 8 mobile HDD trays) 机箱平置，打开前面板，硬盘托架插拔方便容易，不会受前面板干扰.

机构亮点(4/4) 2.5” 3.5” The HDD tray supports either 3.5” or 2.5” disk drive.* *Note: This mechanical design will be phased in around May.

目标应用 数字监控, 例如DVR, NVR, etc. SCADA(Supervisory Control And Data Acquisition) server 工业 (制造业, 生产, 发电, 装配, etc.) 基础设施建设 (水处理, 油气管道, 电力配送, etc.) 公共场所 (智能建筑, 机场, 船舶, 空间站.) Three major function requirement of NVR: network, storage and display The network is used for data transmission, NVR need to receive recorded data of the front-end device and forward the local data to the control center at the same，so two independent network ports are required，one for receiving data and the other for forwarding or is just standby. Storage function is used for data storage of front-end device, because of the special requirements of the security monitoring, storage space must be large enough and support raid in order improve the reliability of data, and number of hard disk interface for storage cannot less than 8. For display, supporting 1 road 1080P HD video decoding and dual independent display is the minimum requirements. Supervisory Control and Data Acquisition (SCADA) refers to a system that reads data from various sensors at a factory, plant or in other remote locations and then sends this data to a central computer which then manages and ontrols the data.

订货信息 Power Supply Options Optional Accessories Part Number Description HPC-7442MB-00XE 4U Barebone chassis for motherboard with 4 mobile HDD trays support Power Supply Options Part Number Description PS8-400ATX-ZE 400W single power supply 1757004335-01 500W single power supply 1757004336-01 700W single power supply 1757004393-01 500W 1+1 redundant power supply 1757004348-01 700W 1+1 redundant power supply Optional Accessories Three major function requirement of NVR: network, storage and display The network is used for data transmission, NVR need to receive recorded data of the front-end device and forward the local data to the control center at the same，so two independent network ports are required，one for receiving data and the other for forwarding or is just standby. Storage function is used for data storage of front-end device, because of the special requirements of the security monitoring, storage space must be large enough and support raid in order improve the reliability of data, and number of hard disk interface for storage cannot less than 8. For display, supporting 1 road 1080P HD video decoding and dual independent display is the minimum requirements. Supervisory Control and Data Acquisition (SCADA) refers to a system that reads data from various sensors at a factory, plant or in other remote locations and then sends this data to a central computer which then manages and ontrols the data. Part Number Description 9680014979 Storage Upgrade Kit (including 4-bay HDD cage, four mobile HDD trays, 4-bay HDD backplanes, one cooling fan)

机箱 Roadmap HPC-7180 ACP-2320 IPC-623 ACP-2000/2010 ACP-5360 ACP-1320 Developing Planning Available Conceptual Performance Support ASMB-9xx 4 2.5” HDD tray 1 expansion 600 mm depth HPC-7180 SATA/SAS HDD tray ACP-2320 20 slot backplane IPC-623 ACP-2000/2010 SAS/ SATA HDD tray ACP-5360 SAS/ SATA HDD tray ACP-4320/4360 SATA/SAS HDD tray ACP-1320 Front I/O IPC-603 ACP-4000/4010 20-slot backplane IPC-622 SAS/ SATA HDD tray ACP-7360 ACP-1010 Value IPC-602 Short Depth @429 IPC-619 Support ATX 4 HDD tray 525 mm depth HPC-7242 IPC-610/611 Support ATX/CEB/EEB 4/8 HDD tray 600 mm depth HPC-7442 Support ATX 4 HDD tray 478 mm depth HPC-7440 Hot selling IPC-610F add USB/PS2 in front Q2‘13 Q2‘13 Most cost effective Add Black Color version IPC-510 Q4‘13 1U 2U 4U 5~7U

Back up

How to Install Optional “Storage Upgrade Kit” to Expand HPC-7442 from Four Mobile HDD Trays to Eight? Removing LED board bracket, front panel cover, slim ODD bracket, and internal HDD bracket aside Installing storage upgrade kit first, then previous slim ODD bracket, and LED board bracket, respectively Installing previous internal HDD bracket back