数字系统设计 Digital System Design

数字系统设计 Digital System Design
EE141 数字系统设计 Digital System Design ------触发器与存储电路王维东 Weidong Wang 浙江大学信息与电子工程学院 College of Information Science & Electronic Engineering 信息与通信网络研究所 Zhejiang University Spring – Lec. #6

任课教师王维东 TA: 浙江大学信息与电子工程学院, 信电楼306 邮箱：wdwang@zju.edu.cn
EE141 任课教师王维东浙江大学信息与电子工程学院, 信电楼306 College of Information Science & Electronic Engineering Zhejiang University, Hangzhou, Tel: (O) Mobile: TA: 陈佳云 Jiayun CHEN， ; 陈彬彬 Binbin CHEN, ; Office Hours：玉泉信电楼 308室（可以微信或邮件联系）. Spring – Lec. #6

Prerequisites预修课程电子电路基础电子线路 C语言 How to learn this Course?
Not only listening, thinking and waiting …. But Exercise, Simulation, Practice!

课程简介课程代码：111C0120 参考书阎石, 数字电子技术基础, 第6版, 高等教育出版社, 2016.
EE141 课程简介课程代码：111C0120 参考书阎石, 数字电子技术基础, 第6版, 高等教育出版社, 2016. 王金明著，数字系统设计与Verilog HDL，电子工业出版社，第6版补充讲义/期中考试前预备 Stanford 大学 108A课程notes. R.H.Katz, G.Borriello, Contemporary Logic Design, second edition,电子工业出版社, 2005. M.M.Mano, 数字设计(第四版), 电子工业出版社, 2010. Spring – Lec. #6

Other Course Info Website: http://mypage.zju.edu.cn/wdwd/教学工作/
Check frequently 答疑玉泉信电楼308室/周三周五下午2:30-5:00 上课课间、课后均可，微信群/数字系统设计2018，短信均可

Grading (考核) Final grades will be computed approximately as follows:
平时（含课程作业、期中考试+小测验、Project、出勤等）30% Class Room Check Homework Sets 作业每周三上交截止期为课后一周内有效。 Project 2 projects (1 or 2 members team) Project-2可选（总评加分1~5分，但不超过平时成绩范围） Finial Exam期末闭卷考试 - 70% 上课说明此门课程的成绩合成：平时成绩包括平时小测验、期中考试、作业、出勤、课堂讨论、论文

授课时间和地点： 2017年春夏学期，地点：紫金港西2-309(多)
周三上午，第1~2节(8:00-9:35) 星期五上午，第1~2节(8:00-9:35) 地点：紫金港西2-309(多) 学在浙里/数字系统设计2018

课程简介课程代码：111C0120 参考书阎石, 数字电子技术基础, 第6版, 高等教育出版社, 2016.
EE141 课程简介课程代码：111C0120 参考书阎石, 数字电子技术基础, 第6版, 高等教育出版社, 2016. 王金明著，数字系统设计与Verilog HDL，电子工业出版社，第6版补充讲义/期中考试前预备 Stanford 大学 108A课程notes. R.H.Katz, G.Borriello, Contemporary Logic Design, second edition,电子工业出版社, 2005. M.M.Mano, 数字设计(第四版), 电子工业出版社, 2010. Spring – Lec. #6

课程结构数字理论知识(必备) 数字电路分析与设计脉冲电路与接口控制器与数字系统微处理器简介与设计数字系统和编码、逻辑代数、门电路
EE141 课程结构数字理论知识(必备) 数字系统和编码、逻辑代数、门电路数字电路分析与设计组合逻辑电路触发器、半导体存贮器、可编程器件时序逻辑电路脉冲电路与接口控制器与数字系统状态机控制器微码控制器测试和验证微处理器简介与设计指令集简单CPU设计 Spring – Lec. #6

EE141 第五章时序电路基础之触发器

Sequential Logic时序逻辑 Sequential Circuits时序 Timing Methodologies定时
EE141 Sequential Logic时序逻辑 Sequential Circuits时序 Simple circuits with feedback Latches记忆元件 Edge-triggered flip-flops啪嗒作响 Timing Methodologies定时 Cascading级联 flip-flops for proper operation Clock skew时钟偏移 Any prior input-level conditions have no effect on the present outputs because combinational logic circuits have no memory. Most digital systems consist of both combinational circuits and memory elements. Spring – Lec. #6

Sequential Circuits Circuits with Feedback
Outputs = f(inputs, past inputs, past outputs) Basis for building "memory" into logic circuits Door combination lock is an example of a sequential circuit State is memory State is an "output" and an "input" to combinational logic Combination storage elements are also memory C1 C2 C3 comparator value equal multiplexer reset open/closed new mux control clock comb. logic state Spring – Lec. #6

Circuits with Feedback
How to control feedback? What stops values from cycling around endlessly X1 X2 • • • Xn switching network Z1 Z2 • • • Zn Spring – Lec. #6

EE141 触发器 flip-flop 5.1 概述一、用于记忆1位二进制信号 1. 有两个能自行保持的状态 2. 根据输入信号可以置成0或1 二、分类 1. 按触发方式（电平，脉冲，边沿） 2. 按逻辑功能（RS, JK, D, T）三、存储器件 ROM、SRAM、DRAM、FLASHROM The most important memory element is the flip-flop, which is made up of an assembly of logic gates. Spring – Lec. #6

Simplest Circuits with Feedback
Two inverters form a static memory cell Will hold value as long as it has power applied How to get a new value into the memory cell? Selectively break feedback path Load new value into cell "0" "1" "stored value" "remember" "load" "data" "stored value" Spring – Lec. #6

Memory with Cross-coupled Gates
EE141 Memory with Cross-coupled Gates Cross-coupled NOR gates Similar to inverter pair, with capability to force output to 0 (reset=1) or 1 (set=1) Cross-coupled NAND gates Similar to inverter pair, with capability to force output to 0 (reset=0) or 1 (set=0) R S Q Q' R S Q Q Q' S' R' R' S' Q Spring – Lec. #6

EE141 5.2 SR锁存器Latch 一、电路结构与工作原理 Spring – Lec. #6

EE141 1 0① ① Spring – Lec. #6

Timing Behavior Setup and Hold Times R S Q Q' Reset Hold Set Race R S
EE141 Timing Behavior Setup and Hold Times R S Q Q' Reset Hold Set Race R S Q \Q 100 Spring – Lec. #6

State Behavior of R-S latch
EE141 State Behavior of R-S latch Truth table of R-S latch behavior Q Q' 0 1 Q Q' 1 0 Q Q' 0 0 Q Q' 1 1 S R Q 0 0 hold unstable Spring – Lec. #6

Theoretical R-S Latch Behavior
EE141 Theoretical R-S Latch Behavior SR=10 SR=00 SR=01 SR=00 SR=10 Q Q' 0 1 Q Q' 1 0 Q Q' 0 0 Q Q' 1 1 SR=01 SR=10 SR=01 SR=01 SR=10 SR=11 SR=11 SR=11 State Diagram States: possible values Transitions: changes based on inputs possible oscillation between states 00 and 11 SR=00 SR=00 SR=11 Spring – Lec. #6

Observed R-S Latch Behavior
EE141 Observed R-S Latch Behavior Very difficult to observe R-S latch in the 1-1 state One of R or S usually changes first Ambiguously returns to state 0-1 or 1-0 A so-called "race condition" Or non-deterministic transition SR=00 Q Q' 0 1 Q Q' 1 0 Q Q' 0 0 SR=10 SR=01 SR=11 Spring – Lec. #6

characteristic equation
EE141 R-S Latch Analysis Break feedback path R S Q Q' Q(t) Q(t+) S R S R Q(t) Q(t+) X X hold reset set not allowed 0 0 1 0 X 1 Q(t) R S characteristic equation Q(t+) = S + R’ Q(t) Spring – Lec. #6

EE141 二、动作特点在任何时刻，输入都能直接改变输出的状态。例： Spring – Lec. #6

EE141 5.3触发器 5.3.1电平触发的触发器一、电路结构与工作原理 X 1 1* Spring – Lec. #6

Gated R-S Latch Control when R and S inputs matter
EE141 Gated R-S Latch enable' S' Q' Q R' R S Control when R and S inputs matter Otherwise, the slightest glitch on R or S while enable is low could cause change in value stored Set Reset S' R' enable' Q Q' 100 Spring – Lec. #6

EE141 Spring – Lec. #6

Clocks Used to keep time Clocks are regular periodic signals
Wait long enough for inputs (R' and S') to settle Then allow to have effect on value stored Clocks are regular periodic signals Period (time between ticks) Duty-cycle (time clock is high between ticks - expressed as % of period) duty cycle (in this case, 50%) period Spring – Lec. #6

Clocks (cont’d) Controlling an R-S latch with a clock
EE141 Clocks (cont’d) Controlling an R-S latch with a clock Can't let R and S change while clock is active (allowing R and S to pass) Only have half of clock period for signal changes to propagate Signals must be stable for the other half of clock period clock' S' Q' Q R' R S clock R' and S' changing stable Spring – Lec. #6

EE141 二、动作特点在CLK=1的全部时间里， S和R的变化都将引起输出状态的变化。 Spring – Lec. #6

EE141 D触发器 X 1 1* Spring – Lec. #6

Cascading Latches Connect output of one latch to input of another
EE141 Cascading Latches Connect output of one latch to input of another How to stop changes from racing through chain? Need to control flow of data from one latch to the next Advance from one latch per clock period Worry about logic between latches (arrows) that is too fast clock R S Q Q' Spring – Lec. #6

提高可靠性，要求每个CLK周期输出状态只能改变1次
EE141 5.3.3 脉冲触发的触发器提高可靠性，要求每个CLK周期输出状态只能改变1次一、电路结构与工作原理 Spring – Lec. #6

Master-Slave Structure
EE141 Master-Slave Structure Break flow by alternating clocks (like an air-lock) Use positive clock to latch inputs into one R-S latch Use negative clock to change outputs with another R-S latch View pair as one basic unit master-slave flip-flop twice as much logic output changes a few gate delays after the falling edge of clock but does not affect any cascaded flip-flops master stage slave stage P P' CLK R S Q Q' Spring – Lec. #6

The 1s Catching Problem In first R-S stage of master-slave FF
EE141 The 1s Catching Problem In first R-S stage of master-slave FF 0-1-0 glitch on R or S while clock is high “caught” by master stage捕捉 Leads to constraints on logic to be hazard-free master stage slave stage P P' CLK R S Q Q' Set 1s catch S R CLK P P' Q Q' Reset Master Outputs Slave Outputs Spring – Lec. #6

问：在CLK=1时，如果S=R=1，主输出“11”，在CLK下降沿到来后，主输出会停在“？？”
EE141 X 1 1* 问：在CLK=1时，如果S=R=1，主输出“11”，在CLK下降沿到来后，主输出会停在“？？” Spring – Lec. #6

EE141 把上次的输出加入反馈，决定输入 J K Q’ 主从 S R Q CLK Spring – Lec. #6

EE141 J 主从 S R K Q Q’ CLK 加入反馈后的效果 Spring – Lec. #6

(5) 列出真值表 X 1 X 1 1* 主从 S R J K Q Q’ CLK CLK=1时的脉冲期间，输入的中间变化会影响输出；
EE141 (5) 列出真值表 X 1 X 1 1* 主从 S R J K Q Q’ CLK CLK=1时的脉冲期间，输入的中间变化会影响输出；要分析整个CLK=1的输入，才能知道输出会是什么。 Spring – Lec. #6

EE141 二、脉冲触发方式的动作特点主从 S R J K Q Q’ CLK Spring – Lec. #6

D Flip-Flop Make S and R complements of each other
EE141 D Flip-Flop Make S and R complements of each other Eliminates 1s catching problem Can't just hold previous value (must have new value ready every clock period) Value of D just before clock goes low is what is stored in flip-flop Can make R-S flip-flop by adding logic to make D = S + R' Q D Q Q' master stage slave stage P P' CLK R S 10 gates Spring – Lec. #6

EE141 5.3.2边沿触发的触发器为了提高可靠性，增强抗干扰能力，希望触发器的次态仅取决于CLK的下降沿（或上升沿）到来时的输入信号状态，与在此前、后输入的状态没有关系。实现方式分类: 1)用CMOS传输门的边沿触发器 2)维持阻塞触发器 3)用门电路tpd的边沿触发器 · · · 这样我们不需要分析整个CLK=1期间的输入变化，只需要分析CLK边沿几个时刻的输入情况。 Spring – Lec. #6

EE141 一、电路结构和工作原理 1、用两个电平触发D触发器组成的边沿触发器 Spring – Lec. #6

EE141 边沿触发器 2、用门电路tpd的边沿触发器 45 Spring ZDMC – Lec. #1 – 5 45

EE141 3.利用CMOS传输门的边沿触发器 X 1 Spring – Lec. #6

4. Edge-Triggered Flip-Flops维持阻塞型
EE141 4. Edge-Triggered Flip-Flops维持阻塞型 More efficient solution: only 6 gates sensitive to inputs only near edge of clock signal (not while high) Q D Clk=1 R S D’ Q’ negative edge-triggered D flip-flop (D-FF) 4-5 gate delays must respect setup and hold time constraints to successfully capture input holds D' when clock goes low holds D when clock goes low characteristic equation Q(t+1) = D 48 Spring ZDMC – Lec. #1 – 6 48

Edge-Triggered Flip-Flops (cont’d)
EE141 Edge-Triggered Flip-Flops (cont’d) Step-by-step analysis Q new D Clk=0 R S D D’ Q D Clk=0 R S D’ new D  old D when clock is low data is held when clock goes high-to-low data is latched Spring – Lec. #6

EE141 Edge-Triggered Flip-Flops (cont’d) D = 0, Clk High 1 Act as inverters D’ D D’ Hold state R Q Clk=1 1 S D D’ D Spring – Lec. #6

EE141 Edge-Triggered Flip-Flops (cont’d) D = 1, Clk High 1 1 ® 0 0 ® 1 D’ D D’ R Q Clk=1 1 S D 0 ® 1 D’ D 1 Spring – Lec. #6

EE141 Edge-Triggered Flip-Flops (cont’d) D = 1, Clk LOW 1 Act as inverters D’ D D’ 0 ® 1 R Q Clk=0 1 ® 0 1 S 0 ® 1 D 1 D’ D Spring – Lec. #6

EE141 Edge-Triggered Flip-Flops (cont’d) Positive edge-triggered Inputs sampled on rising edge; outputs change after rising edge Negative edge-triggered flip-flops Inputs sampled on falling edge; outputs change after falling edge 100 D CLK Qpos Qpos' Qneg Qneg' positive edge-triggered FF negative edge-triggered FF Spring – Lec. #6

5. Negative Edge Trigger FF in Verilog
module d_ff (q, q_bar, data, clk); input data, clk; output q, q_bar; reg q; assign q_bar = ~q; clk) begin q <= data; end endmodule Spring – Lec. #6

EE141 5.3.4 触发器的逻辑功能分类 5.6.1 触发器按逻辑功能的分类时钟控制的触发器中由于输入方式不同（单端，双端输入）、次态（）随输入变化的规则不同注：如果没有特别指明，以后说的有时钟的触发器默认都是指边沿触发的触发器 Spring – Lec. #6

一、SR触发器 1. 定义，凡在时钟信号作用下，具有如下功能的触发器称为SR触发器
EE141 一、SR触发器 1. 定义，凡在时钟信号作用下，具有如下功能的触发器称为SR触发器约束条件 1 1* Spring – Lec. #6

EE141 二、JK触发器 1.定义 1 Spring – Lec. #6

Spring – Lec. #6

EE141 三、T触发器 1. 定义：凡在时钟信号作用下，具有如下功能的触发器 1 Spring – Lec. #6

EE141 四、D触发器 1. 定义：凡在时钟信号作用下，具有如下功能的触发器 1 。。。。 Spring – Lec. #6

EE141 逻辑功能：是与输入及在CLK作用后稳态之间的关系（RS, JK, D, T）电路结构形式：具有不同的动作特点（转换状态的动态过程）（同步，主从，边沿） Spring – Lec. #6

Comparison of Latches and Flip-Flops
EE141 Comparison of Latches and Flip-Flops D Q D CLK Qedge Qlatch CLK positive edge-triggered flip-flop D Q G CLK transparent (level-sensitive) latch behavior is the same unless input changes while the clock is high Spring – Lec. #6

Comparison of Latches and Flip-Flops (cont’d)
EE141 Comparison of Latches and Flip-Flops (cont’d) Type When inputs are sampled When output is valid unclocked always propagation delay from input change latch level-sensitive clock high propagation delay from input change latch (Tsu/Th around falling or clock edge (whichever is later) edge of clock) master-slave clock high propagation delay from falling edge flip-flop (Tsu/Th around falling of clock edge of clock) negative clock hi-to-lo transition propagation delay from falling edge edge-triggered (Tsu/Th around falling of clock flip-flop edge of clock) Spring – Lec. #6

EE141 5.3.5 触发器的动态特性一、输入信号宽度二、传输延迟时间 Spring – Lec. #6

一、建立时间二、保持时间三、传输延迟时间四、最高时钟频率
EE141 一、建立时间二、保持时间三、传输延迟时间四、最高时钟频率 Spring – Lec. #6

Typical Timing Specifications
EE141 Typical Timing Specifications Positive edge-triggered D flip-flop Setup and hold times Minimum clock width Propagation delays (low to high, high to low, max and typical) Th 5ns Tw 25ns Tplh 25ns 13ns Tphl 40ns 25ns Tsu 20ns D CLK Q all measurements are made from the clocking event that is, the rising edge of the clock Spring – Lec. #6

POTENTIAL TIMING PROBLEM IN FF CIRCUITS
The potential timing problem is this: because Q1 will change on the NGT of the clock pulse, the J2 input of Q2 will be changing as it receives the same NGT. This could lead to an unpredictable response at Q2. Spring – Lec. #6

Cascading Edge-triggered Flip-Flops级联问题
EE141 Cascading Edge-triggered Flip-Flops级联问题 Shift register New value goes into first stage While previous value of first stage goes into second stage Consider setup/hold/propagation delays (prop must be > hold) CLK IN Q0 Q1 D Q OUT Fortunately, all modern edge-triggered FFs have hold time requirements that are 5 ns or less; most have tH = 0, which means that they have no hold time requirement. 100 IN Q0 Q1 CLK Spring – Lec. #6

Cascading Edge-triggered Flip-Flops (cont’d)
EE141 Cascading Edge-triggered Flip-Flops (cont’d) Why this works Propagation delays exceed hold times Clock width constraint exceeds setup time This guarantees following stage will latch current value before it changes to new value Tsu 4ns Tp 3ns Th 2ns In Q0 Q1 CLK timing constraints guarantee proper operation of cascaded components assumes infinitely fast distribution of the clock Spring – Lec. #6

Clock Skew时钟偏移 The problem
EE141 Clock Skew时钟偏移 The problem Correct behavior assumes next state of all storage elements determined by all storage elements at the same time Difficult in high-performance systems because time for clock to arrive at flip-flop is comparable to delays through logic (and will soon become greater than logic delay) Effect of skew on cascaded flip-flops: original state: IN = 0, Q0 = 1, Q1 = 1 due to skew, next state becomes: Q0 = 0, Q1 = 0, and not Q0 = 0, Q1 = 1 CLK1 is a delayed version of CLK0 In Q0 Q1 CLK0 CLK1 100 Spring – Lec. #6

Summary of Latches and Flip-Flops
EE141 Summary of Latches and Flip-Flops Development of D-FF Level-sensitive used in custom integrated circuits can be made with 4 switches Edge-triggered used in programmable logic devices Good choice for data storage register Historically J-K FF was popular but now never used Similar to R-S but with 1-1 being used to toggle output (complement state) Good in days of TTL/SSI (more complex input function: D = JQ' + K'Q Not a good choice for PLAs as it requires two inputs Can always be implemented using D-FF Preset and clear inputs are highly desirable on flip-flops Used at start-up or to reset system to a known state Spring – Lec. #6

Flip-Flop Features Reset (set state to 0): R
EE141 Flip-Flop Features Reset (set state to 0): R Synchronous: Dnew = R' • Dold (when next clock edge arrives) Asynchronous: doesn't wait for clock, quick but dangerous Preset or set (set state to 10: S (or sometimes P) Synchronous: Dnew = Dold + S (when next clock edge arrives) Both reset and preset Dnew = R' • Dold + S (set-dominant) Dnew = R' • Dold + R'S (reset-dominant) Selective input capability (input enable/load): LD or EN Multiplexer at input: Dnew = LD' • Q + LD • Dold Load may/may not override reset/set (usually R/S have priority) Complementary outputs: Q and Q' Spring – Lec. #6

触发器Flip-Flop分类逻辑功能分类逻辑功能指按触发器的次态和现态及输入信号之间的逻辑关系. RS锁存器 JK触发器 T触发器
EE141 触发器Flip-Flop分类逻辑功能分类 RS锁存器 JK触发器 T触发器 D触发器逻辑功能指按触发器的次态和现态及输入信号之间的逻辑关系. 特性表特性方程状态转换图 Spring – Lec. #6

RS 锁存器特性方程Qn+1=S+R’Qn RS Latch的状态转换图特性表/真值表 1 0 1 1 0 0 0 0 0
EE141 RS 锁存器特性方程Qn+1=S+R’Qn RS Latch的状态转换图特性表/真值表 1 S=1,R=0 S=0,R=1 S=X,R=0 S=0,R=X S R Qn Qn+1 保持复位置位不定 Spring – Lec. #6

JK 触发器特性方程:Qn+1=JQn’+K’Qn JK FF的状态转换图特性表/真值表 1 0 1 1 0 0 0 0 0
EE141 JK 触发器特性方程:Qn+1=JQn’+K’Qn JK FF的状态转换图特性表/真值表 1 J=1,K=X J=X,K=1 J=X,K=0 J=0,K=X J K Qn Qn+1 保持复位置位翻转 Spring – Lec. #6

T 触发器特性方程:Qn+1=TQn’+T’Qn T FF的状态转换图特性表/真值表 T’触发器：T=1, Qn+1=Qn’ 1
EE141 T 触发器特性方程:Qn+1=TQn’+T’Qn T FF的状态转换图特性表/真值表 T’触发器：T=1, Qn+1=Qn’ 1 T=1 T=0 T Qn Qn+1 保持翻转 JK触发器的两个输入端连在一起作为T端，可以构成T Flip-flop Spring – Lec. #6

D 触发器特性方程:Qn+1=D D FF的状态转换图特性表/真值表 1 1 1 1 0 0 0 0 1 0 1 0 1 D=1 D=0
EE141 D 触发器特性方程:Qn+1=D D FF的状态转换图特性表/真值表 1 D=1 D=0 D Qn Qn+1 reset set Spring – Lec. #6

EE141 采用D 触发器实现JK触发器 K D clk Q Q’ J Clk Spring – Lec. #6

Timing Methodologies Rules for interconnecting components and clocks
EE141 Timing Methodologies Rules for interconnecting components and clocks Guarantee proper operation of system when strictly followed Approach depends on building blocks used for memory elements Focus on systems with edge-triggered flip-flops Found in programmable logic devices Many custom integrated circuits focus on level-sensitive latches Basic rules for correct timing: (1) Correct inputs, with respect to time, are provided to the flip-flops (2) No flip-flop changes state more than once per clocking event Spring – Lec. #6

Timing Methodologies (cont’d)
EE141 Timing Methodologies (cont’d) Definition of terms clock: periodic event, causes state of memory element to change; can be rising or falling edge, or high or low level setup time: minimum time before the clocking event by which the input must be stable (Tsu) hold time: minimum time after the clocking event until which the input must remain stable (Th) input clock Tsu Th clock data changing stable D Q there is a timing "window" around the clocking event during which the input must remain stable and unchanged in order to be recognized Spring – Lec. #6

D LATCH (TRANSPARENT LATCH)
5.4 寄存器 D LATCH (TRANSPARENT LATCH) Spring – Lec. #6

Actual Ics 多位成组 Spring – Lec. #6

SERIAL DATA TRANSFER: SHIFT REGISTERS
Spring – Lec. #6

EE141 5.5 半导体存储器 A major advantage of digital over analog systems is the ability to store easily large quantities of digital information and data for short or long periods. Spring – Lec. #6

5.5 半导体存储器 memory devices 1 概述能存储大量二值信息的器件一、一般结构形式！单元数庞大
EE141 5.5 半导体存储器 memory devices 1 概述能存储大量二值信息的器件一、一般结构形式 flip-flop? ！单元数庞大！输入/输出引脚数目有限输入/出电路 I/O 输入/出控制 Spring – Lec. #6

（Random-Access-Memory） 2、从工艺分： ①双极型 ②MOS型
EE141 二、分类 1、从存/取功能分： ①只读存储器 (Read-Only-Memory） ②随机读/写（Random-Access-Memory） 2、从工艺分： ①双极型 ②MOS型 Spring – Lec. #6

5.5 随机存储器RAM random-access memory
EE141 5.5 随机存储器RAM random-access memory 5.5.1 静态随机存储器（SRAM）STATIC RAM 一、结构与工作原理 Spring – Lec. #6

EE141 二、SRAM的存储单元六管N沟道增强型MOS管 Spring – Lec. #6

Logic symbols (a) the 2147H RAM chip; (b) the MCM6206C RAM.
Spring – Lec. #6

Symbol and mode table for the CMOS MCM6264C.
Spring – Lec. #6

5.5.2* 动态随机存储器（DRAM）DYNAMIC RAM
EE141 5.5.2* 动态随机存储器（DRAM）DYNAMIC RAM 动态存储单元是利用MOS管栅极电容可以存储电荷的原理 Dynamic RAMs store 1s and 0s as charges on a small MOS capacitor (typically a few picofarads). In modern DRAM chips, each memory cell must be refreshed typically every 2, 4, or 8 ms, or its data will be lost. Spring – Lec. #6

Cell arrangement in a dynamic RAM
DRAM TECHNOLOGY Memory Modules single-in-line memory module (SIMM) dual-in-line memory module (DIMM) SODIMM RIMM DRDRAM FPM DRAM EDO DRAM SDRAM DDRSDRAM SLDRAM Spring – Lec. #6

Simplified architecture of the TMS44100 ; RAS>CAS timing
Spring – Lec. #6

5.5.3 ROM-READ-ONLY MEMORIES 1 掩模ROM 一、结构
EE141 5.5.3 ROM-READ-ONLY MEMORIES 1 掩模ROM 一、结构 Spring – Lec. #6

EE141 二、举例 Spring – Lec. #6

A0~An-1 W(2n-1) Dm Spring 2018 – Lec. #6 W0 D0 地址数据 1 A1 A0 D3 D2
EE141 A0~An-1 W0 W(2n-1) D0 Dm 地址数据 A1 A0 D3 D2 D1 D0 1 Spring – Lec. #6

两个概念：存储矩阵的每个交叉点是一个“存储单元”，存储单元中有器件存入“1”，无器件存入“0” 存储器的容量：“字数 x 位数”
EE141 两个概念：存储矩阵的每个交叉点是一个“存储单元”，存储单元中有器件存入“1”，无器件存入“0” 存储器的容量：“字数 x 位数” Spring – Lec. #6

掩模ROM的特点：出厂时已经固定，不能更改，适合大量生产简单，便宜，非易失性nonvolatile
EE141 掩模ROM的特点：出厂时已经固定，不能更改，适合大量生产简单，便宜，非易失性nonvolatile Spring – Lec. #6

ROM ARCHITECTURE Spring – Lec. #6

Typical timing for a ROM read operation.
Spring – Lec. #6

2 可编程ROM（PROM）Programmable ROMs
EE141 2 可编程ROM（PROM）Programmable ROMs 总体结构与掩模ROM一样，但存储单元不同 “one-time programmable” (OTP) ROMs Spring – Lec. #6

2 可编程ROM（PROM）总体结构与掩模ROM一样，但存储单元不同写入时，要使用编程器 Spring 2018 – Lec. #6
EE141 2 可编程ROM（PROM）总体结构与掩模ROM一样，但存储单元不同写入时，要使用编程器 Spring – Lec. #6

3 可擦除的可编程ROM（EPROM） Erasable Programmable ROM
EE141 3 可擦除的可编程ROM（EPROM） Erasable Programmable ROM 总体结构与掩模ROM一样，但存储单元不同一、用紫外线擦除的PROM（UVEPROM） nonvolatile Spring – Lec. #6

二、电可擦除的可编程ROM（E2PROM）
EE141 二、电可擦除的可编程ROM（E2PROM） Electrically Erasable PROM 总体结构与掩模ROM一样，但存储单元不同 Without a UV light source and a special PROM programmer unit Spring – Lec. #6

Electrically Erasable PROM
Another advantage of the EEPROM over the EPROM is the ability to erase and rewrite individual bytes (eight-bit words) in the memory array electrically. This byte erasability makes it much easier to make changes in the data stored in an EEPROM. The early EEPROMs, such as Intel’s 2816, required appropriate support circuitry external to the memory chips, included the 21-V programming voltage (VPP). The newer devices, such as the Intel 2864, have integrated this support circuitry onto the same chip with the memory array, it requires only a single 5-V power pin. Spring – Lec. #6

Timing for the write operation.
Spring – Lec. #6

三、快闪存储器（Flash Memory）
EE141 The challenge for semiconductor engineers was to fabricate a nonvolatile memory with the EEPROM’s in-circuit electrical erasability, but with densities and costs much closer to those of EPROMs, while retaining the high-speed read access of both. 三、快闪存储器（Flash Memory）为提高集成度，省去T2（选通管）改用叠栅MOS管（类似SIMOS管） Spring – Lec. #6

Trade-offs for semiconductor nonvolatile memories show that complexity and cost increase as erase and programming flexibility increases. A typical flash memory has a write time of 10 ms per byte compared to 100 for the most advanced EPROM and 5 ms for EEPROM (which includes automatic byte erase time). Spring – Lec. #6

5.5.4 存储器容量的扩展 1. 位扩展方式适用于每片RAM,ROM字数够用而位数不够时接法：将各片的地址线、读写线、片选线并联即可
EE141 5.5.4 存储器容量的扩展 1. 位扩展方式适用于每片RAM,ROM字数够用而位数不够时接法：将各片的地址线、读写线、片选线并联即可例：用八片1024 x 1位→ 1024 x 8位的RAM Spring – Lec. #6

2. 字扩展方式适用于每片RAM,ROM位数够用而字数不够时例：用四片256 x 8位→1024 x 8位 RAM 1024 x 8
EE141 2. 字扩展方式适用于每片RAM,ROM位数够用而字数不够时例：用四片256 x 8位→1024 x 8位 RAM 1024 x 8 RAM Spring – Lec. #6

EE141 1 Spring – Lec. #6

5.5.5 用存储器实现组合逻辑函数一、基本原理从ROM的数据表可见：若以地址线为输入变量，则数据线即为一组关于地址变量的逻辑函数
EE141 5.5.5 用存储器实现组合逻辑函数一、基本原理从ROM的数据表可见：若以地址线为输入变量，则数据线即为一组关于地址变量的逻辑函数地址数据 A1 A0 D3 D2 D1 D0 1 A0~An-1 W0 W(2n-1) Spring – Lec. #6

5.5.5 用存储器实现组合逻辑函数一、基本原理从ROM的数据表可见：若以地址线为输入变量，则数据线即为一组关于地址变量的逻辑函数
EE141 5.5.5 用存储器实现组合逻辑函数一、基本原理从ROM的数据表可见：若以地址线为输入变量，则数据线即为一组关于地址变量的逻辑函数地址数据 A1 A0 D3 D2 D1 D0 1 Spring – Lec. #6

EE141 地址数据 A1 A0 D3 D2 D1 D0 1 Spring – Lec. #6

EE141 二、举例 Spring – Lec. #6

SPECIAL MEMORY FUNCTIONS
Cache Memory First-In, First-Out Memory (FIFO) Circular Buffers Spring – Lec. #6

实例：PC to Memory (a) CPU address bus driving ROM or static-RAM memory;
(b) CPU addresses driving a multiplexer that is used to multiplex the CPU address lines into the DRAM. Spring – Lec. #6

实例：Function Generator
Spring – Lec. #6

课后作业查阅：作业：自学Verilog HDL语言阅读：国际电路公司NXP，onsemi，fairchild，TI等的
EE141 课后作业查阅：国际电路公司NXP，onsemi，fairchild，TI等的触发器、同步计数器、异步计数器芯片的型号手册、电参数、速度…… 图书馆资源：电子器件天地, 软件作业：《见学在浙里》自学Verilog HDL语言阅读：推荐英文版电子书，“Digital_Systems_Principles_and_Applications”，CHAPTER 5 详细、实用较强； ch ; Ch Spring – Lec. #6

数字系统设计 Digital System Design

Similar presentations

Presentation on theme: "数字系统设计 Digital System Design"— Presentation transcript:

Similar presentations

About project

反馈

请登录

Auth with social network:

数字系统设计 Digital System Design

Similar presentations

Presentation on theme: "数字系统设计 Digital System Design"— Presentation transcript:

Similar presentations

About project

反馈