瑞虎SQR7240T11T车型与SQR7247车型技术资料区别 售后服务部 瑞虎SQR7240T11T车型与SQR7247车型技术资料区别

Difference in Technical Data between Tiggo SQR7240T11T and SQR7247 After-sales Service Department Difference in Technical Data between Tiggo SQR7240T11T and SQR7247

一、整车差异件清单

I. List of Different Accessory on Finished Vehicle

差异件清单 SQR7240T11T SQR7247 零件名称 零件号 数量 发动机总成 B11-1000040 1 —— 排气歧管 隔热罩 T11-1008140 4 螺栓 480-1008143 3 悬置双头螺柱 T11-1001412 左悬置支架 T11-1001211DA T11-1001211CA

List of Different Accessory SQR7240T11T SQR7247 Accessory Name Accessory No. Quantity Accessory Name Engine Assembly B11-1000040 1 —— Exhaust Manifold T11-1008111 2 Heat Shroud T11-1008140 4 Bolt 480-1008143 3 Mount Double-end Bolt T11-1001412 Left Mount Bracket T11-1001211DA T11-1001211CA

接上页 零件名称 零件号 数量 前悬置支架 T11-1001611DA 1 T11-1001611CA 后悬置支架 T11-1001811DA T11-1001811BA 空气滤清器带引气管总成 T11-1109110CA 　1 T11-1109110 进气橡胶管 T11-1109210BA T11-1109410 曲轴箱通风软管 T11-1014011BA T11-1014011 油门拉线 T11-1108210BA T11-1108210 排气中管 T11-1203310CA T11-1203310 排气前管 T11-1203110DA T11-1203110CA 连接管 T11-1203210 —— 螺栓 Q184C1230 2 密封垫片 B11-1205311 5

Connected to Preceding Page Accessory Name Accessory No. Quantity Accessory Name Front Mount Bracket T11-1001611DA 1 Front mount Bracket T11-1001611CA Rear Mount Bracket T11-1001811DA T11-1001811BA Air Strainer with Intake Pipe Assembly T11-1109110CA 　 1 T11-1109110 Air Intake Rubber Pipe T11-1109210BA T11-1109410 Crankcase Ventilation Hose T11-1014011BA T11-1014011 Accelerator Guy T11-1108210BA T11-1108210 Exhaust Middle Pipe T11-1203310CA T11-1203310 Exhaust Front Pipe T11-1203110DA T11-1203110CA Connecting Pipe T11-1203210 —— Bolt Q184C1230 2 Seal Gasket B11-1205311 5

零件名称 零件号 数量 吊块Ⅰ T11-1203261 6 —— 散热器总成 T11-1301110CA 1 T11-1301110 风扇总成 T11-1308010CA 排管总成 T11-1104001FA T11-1104001 燃油箱带油泵总成 T11-1101001FA T11-1101001 燃油箱总成 T11-1101110BA T11-1101110 燃油箱密封圈 A11-1101151 油泵密封圈 T11-1106611 2 燃油箱压盖 A11-1101153 油泵挡圈 T11-1106613 电动燃油泵 T11-1106610CA 电动燃油泵总成 T11-1106610 进油管Ⅰ总成 T11-1104110DA T11-1104110

Accessory Name Accessory No. Quantity Sling Block I T11-1203261 6 —— Radiator Assembly T11-1301110CA 1 T11-1301110 Fan Assembly T11-1308010CA Exhaust Pipe Assembly T11-1104001FA T11-1104001 Fuel Tank with Oil Pump Assembly T11-1101001FA T11-1101001 Fuel Tank Assembly T11-1101110BA T11-1101110 Fuel Tank Seal Ring A11-1101151 Oil Pump Seal Ring T11-1106611 2 Fuel Tank Cover A11-1101153 Oil Pump Snap Ring T11-1106613 Electric Fuel Pump T11-1106610CA Electric Fuel Pump Assembly T11-1106610 Inlet Oil Pipe I Assembly T11-1104110DA T11-1104110

零件名称 零件号 数量 进油管Ⅱ总成 T11-1104120CA 1 T11-1104120 进油管VI总成 T11-1104160FA 进回油管总成 T11-1104140 单耳无级卡箍 AQ60213 　—— AQ60214 回油软管 T11-1104211FA 加油管总成 T11-110310BA 回油管Ⅲ总成 T11-1104250FA T11-1104220 燃油蒸汽管Ⅰ总成 T11-1104310FA 燃油箱护板 T11-1101121 燃油蒸汽软管Ⅲ T11-1104351 2 燃油箱固定带总成Ⅰ T11-1100015 燃油箱固定带总成 T11-1100010 燃油箱固定带总成Ⅱ T11-1100025

Inlet and Back Oil Pipe Assembly Fuel Tank Fixed Belt Assembly Accessory Name Accessory No. Quantity Inlet Oil Pipe II Assembly T11-1104120CA 1 T11-1104120 Inlet Oil Pipe VI Assembly T11-1104160FA Inlet and Back Oil Pipe Assembly T11-1104140 Unilateral Stepless Clamp AQ60213 　—— AQ60214 Back Oil Hose T11-1104211FA Filler Pipe Assembly T11-110310BA Back Oil Pipe III Assembly T11-1104250FA Back Pipe III Assembly T11-1104220 Fuel Steam Hose I Assembly T11-1104310FA Fuel Tank Protect Panel T11-1101121 Fuel Steam Hose III T11-1104351 2 ⅠFuel Tank Fixed Belt Assembly I T11-1100015 Fuel Tank Fixed Belt Assembly T11-1100010 Fuel Tank Fixed Belt Assembly II T11-1100025

零件名称 零件号 数量 燃油箱固定带总成Ⅲ T11-1100035 1 —— ECU控制单元 B11-3605010 T11-3605010BA TCU控制单元 B11-3605020 　 —— 氧传感器Ⅰ总成 B11-1205110 T11-1205110 氧传感器Ⅱ总成 B11-1205310 —— 　 空气流量计总成 B11-1109510BA ECU支架 T11-3605015CA T11-3605011 三元催化器总成 B11-1205210AB 催化器总成 T11-1205210 氧传感器线束固定管夹 T11-1205411BA 单耳无级卡箍 AQ60218

Accessory Name Accessory No. Quantity Fuel Tank Fixed Belt Assembly III T11-1100035 1 —— ECU Control Unit B11-3605010 T11-3605010BA TCU Control Unit B11-3605020 　 —— Oxygen Sensor I Assembly B11-1205110 T11-1205110 Oxygen Sensor II Assembly B11-1205310 —— 　 Airflow Meter Assembly B11-1109510BA ECU Bracket T11-3605015CA T11-3605011 3-way Catalytic Converter Assembly B11-1205210AB Catalytic Converter Assembly T11-1205210 Oxygen Sensor Harness Fixed Clip T11-1205411BA Unilateral stepless Clamp AQ60218

零件名称 零件号 数量 前舱线束 T11-3724010TA 1 前舱线束总成 T11-3724010 仪表板线束 T11-3724030TA 仪表板线束总成 T11-3724030 室内线束 T11-3724050TA 室内线束总成 T11-3724050 发动机线束 T11-3724180TA 发动机线束总成 T11-3724180BA 前舱电器盒总成 T11-3723010BA T11-3723010 仪表电器盒总成 T11-3723060BA 　 —— 正极线束总成　 T11-3724011TA 2 T11-3724011 金属扎带 T11-3723019 —— 螺栓 Q1840610 ISU支架 T11-3600050 Q1840640 风扇控制器 B11-3600020

Accessory Name Accessory No. Quantity Engine Compartment Harness T11-3724010TA 1 Engine Compartment Harness Assembly T11-3724010 Instrument Panel Harness T11-3724030TA Instrument Panel Harness Assembly T11-3724030 In-door Harness T11-3724050TA In-door Harness Assembly T11-3724050 Engine Harness T11-3724180TA Engine harness Assembly T11-3724180BA Engine Compartment Electric Box Assembly T11-3723010BA T11-3723010 Instrument Electric Box Assembly T11-3723060BA 　 —— Anode Harness Assembly T11-3724011TA 2 Anode Harness Assembly 　 T11-3724011 Metal Sheaf Belt T11-3723019 —— Bolt Q1840610 ISU Bracket T11-3600050 Q1840640 Fan Control B11-3600020

零件名称 零件号 数量 螺栓 Q1800616 2 —— 组合仪表 T11-3820010DB 1 T11-3820010 蓄电池托盘 T11-3703011BA T11-3703011 变速器总成 T11-1500010 QR523-1700010 变速箱机油标尺 T11-1502150 进油管总成 T11-1503020 回油管总成 T11-1503040 空心螺栓 B11-1503011 密封垫片 B11-1503013 4 通气软管总成 B11-1503060 卡箍 B11-1503061 单管夹片 B11-1503063

Accessory Name Accessory No. Quantity Bolt Q1800616 2 —— Combination Instrument T11-3820010DB 1 T11-3820010 Battery Tray T11-3703011BA T11-3703011 Transmission Assembly T11-1500010 QR523-1700010 Transmission Engine Oil Ruler T11-1502150 Inlet Oil Pipe Assembly T11-1503020 Back Oil Pipe Assembly T11-1503040 Tubular Bolt B11-1503011 Seal Gasket B11-1503013 4 Air Hose Assembly B11-1503060 Clamp B11-1503061 Unit Pipe Clip B11-1503063

零件名称 零件号 数量 螺栓 Q1840612 2 —— 左等速节驱动轴总成 T11-2203010DA 1 左前驱动轴总成 T11-2203020BC 右等速节驱动轴总成 T11-2203020DA 右前驱动轴总成 自动换档操纵机构总成 T11-1504010 换档操纵机构总成 T11-1703010 软轴拉线总成 T11-1504310 T11-1703090 组合螺母 Q32208 制动踏板总成 T11-3504010DA T11-3504010 储液罐总成 T11-3505110DA T11-3505110

Accessory Name Accessory No. Quantity Bolt Q1840612 2 —— Left Constant Velocity Joint Drive Shaft Assembly T11-2203010DA 1 Left Front Drive Shaft Assembly T11-2203020BC Right Constant Velocity Joint Drive Shaft Assembly T11-2203020DA Right Front Drive Shaft Assembly Automatic Shift Control Mechanism Assembly T11-1504010 T11-1703010 Soft Shaft harness Assembly T11-1504310 T11-1703090 combination Nut Q32208 Automatic Pedal Assembly T11-3504010DA T11-3504010 Fluid Reservoir Assembly T11-3505110DA T11-3505110

零件名称 零件号 数量 油泵固定支架 T11-3412021BA 1 T11-3412021 前副车架总成 T11-2810010AT T11-2810010 排气管吊钩 T11-2810411 　 —— 　 —— 仪表板 T11-5305001BB T11-5305001BA 换档面罩 T11-5305940BA T11-5305933 堵盖2# B11-5110043 保护膜F S11-5402029 车内附件 T11-5300002DA T11-5300002 前挡板减振垫 T11-5310010DA T11-5310010

Accessory Name Accessory No. Quantity Oil Pump Fixed Support T11-3412021BA 1 T11-3412021 Rear Sub-frame Assembly T11-2810010AT T11-2810010 Discharge Pipe Hook T11-2810411 　 —— 　 —— Instrument Panel T11-5305001BB T11-5305001BA Shift Cover T11-5305940BA T11-5305933 End Cover2# B11-5110043 Protect Membrane F S11-5402029 Interior Accessories T11-5300002DA T11-5300002 Front Fender Damper Gasket T11-5310010DA T11-5310010

零件名称 零件号 数量 发动机仓隔热垫 T11-5310311DA 1 T11-5310311 白车身总成 T11-5000010BD T11-5000010 车身骨架总成 T11-5010010BD T11-5010010 车身下部总成 T11-5100010BD T11-5100010 发动机舱总成 T11-5300010BD T11-5300010 左前纵梁轮罩总成 T11-8403010BD T11-8403010 左前纵梁总成 T11-5101030BD T11-5101030 左前纵梁前部总成 T11-5101300BD T11-5101300 左前纵梁前部本体总成 T11-5101310BD T11-5101310

Accessory Name Accessory No. Quantity Engine Compartment Heat Shield T11-5310311DA 1 T11-5310311 Body in White Assembly T11-5000010BD T11-5000010 Body Frame Assembly T11-5010010BD T11-5010010 Body lower part Assembly T11-5100010BD T11-5100010 Engine Compartment Assembly T11-5300010BD T11-5300010 Left Front Side Member Wheal Cowl Assembly T11-8403010BD T11-8403010 Left Front Side Member Assembly T11-5101030BD T11-5101030 Front of left Front Side Member Assembly T11-5101300BD T11-5101300 Front Part of Left Front Side Member Assembly T11-5101310BD Front Part of Left Front Side Member Assembly T11-5101310

零件名称 零件号 数量 左前纵梁前部本体 T11-5101311BD 1 T11-5101311 蓄电池支撑板总成 T11-5100380BD T11-5100380 蓄电池支撑板 T11-5100377BD T11-5100377 蓄电池托架总成 T11-5100370BD T11-5100370 蓄电池托架 T11-5100375BD T11-5100375 中排气管吊杆 T11-5101457 白车身总成（带天窗） T11-5000010BE 白车身总成 T11-5000010BA 车身骨架总成（带天窗） T11-5010010BE 车身骨架总成 T11-5010010BA

Accessory Name Accessory No. Quantity Front Part of Left Front Side Member T11-5101311BD 1 T11-5101311 Battery Anchor Plate Assembly T11-5100380BD T11-5100380 Battery Anchor Plate T11-5100377BD T11-5100377 Battery Bracket Assembly T11-5100370BD T11-5100370 Battery Bracket T11-5100375BD T11-5100375 Middle Exhaust Pipe Suspender T11-5101457 Body in White Assembly (Sky Light Equipped) T11-5000010BE Body in White Assembly T11-5000010BA Body Frame Assembly (Sky Light Equipped） T11-5010010BE Body Frame Assembly T11-5010010BA

二、发动机部分

II. Engine

1、 发动机机械部分 SQR7240T11T与SQR7247相比，发动机机械部分除发动机悬置、进气系统、排气系统有差异外，其它部分同SQR7247，请参照我部前期发放的《东方之子三菱发动机机械部分维修手册》 。

1) Mechanical Part of Engine The mechanical part of the engine of SQR7240T11T is the same as that of SQR7247, except the difference in engine mount, air intake system and discharge system. Please refer to the Maintenance Manual of Mechanical Part of Mitsubishi Engine of Eastar published by this Department.

左悬置 ⑥ ③ ⑤ ② ① ④ ⑥ 序号 名称 图号 数量 扭 矩 ① 左悬置软垫总成 T11-1001110BA 1 ② 左悬置支架   ② 左悬置支架 T11-1001211DA ③ 六角法兰面螺栓 Q184C1025 4 70±5N.m ④ Q184C10125TF6 ⑤ 六角法兰面螺母 Q330C10 ⑥ 自锁螺母 AQ330B12 80±5N.m ③ ① ④ ⑤ ⑥ ② ⑥

Left Mount Soft Gasket Assembly Left Suspension Serial No. Name and Figure No. Quantity Torque ① Left Mount Soft Gasket Assembly T11-1001110BA 1   ② Left Mount Bracket T11-1001211DA ③ Hexagonal Flange Bolt Q184C1025 4 70±5N.m ④ Q184C10125TF6 ⑤ Hexagonal Flange Nut Q330C10 ⑥ Locknut AQ330B12 80±5N.m ③ ① ④ ⑤ ⑥ ② ⑥

右悬置 ④ ③ ⑤ ①① ②① 序号 名称 图号 数量 扭 矩 ① 右悬置软垫总成T11-1001310 1 ②   ② 六角法兰面螺栓Q184C1025 2 70±5N.m ③ 螺栓 Q1400820 35±5N.m ④ 六角法兰面螺母Q330C10 ⑤ 六角法兰面螺栓Q184C1040TF6 ⑤ ②① ①① ③ ④

Right Mount Soft Gasket Assembly T11-1001310 Right Suspension Serial No. Name and Figure No. Quantity Torque ① Right Mount Soft Gasket Assembly T11-1001310 1   ② Hexagonal Flange Bolt Q184C1025 2 70±5N.m ③ Bolt Q1400820 35±5N.m ④ Hexagonal Flange Nut Q330C10 ⑤ Q184C1040TF6 ⑤ ②① ①① ③ ④

前悬置 ②① ①① ⑥ ③、④ ⑤ 序号 名称 图号 数量 扭 矩 ① 前悬置软垫总成T11-1001510CA 1 ②   ② 前悬置支架T11-1001611DA ③ 六角法兰面螺栓Q184C1090 70±5N.m ④ 六角法兰面螺母Q330C10 ⑤ 六角法兰面螺栓Q184C1025 2 ⑥ 六角法兰面螺栓Q184B1225TF6 80±5N.m ③、④ ①① ⑤ ②① ⑥

Front Mount Soft Gasket Assembly Front Suspension Serial No. Name and Figure No. Quantity Torque ① Front Mount Soft Gasket Assembly T11-1001510CA 1   ② Front Mount Bracket T11-1001611DA ③ Hexagonal Flange Bolt Q184C1090 70±5N.m ④ Hexagonal Flange Nut Q330C10 ⑤ Q184C1025 2 ⑥ Q184B1225TF6 80±5N.m ③、④ ①① ⑤ ②① ⑥

后悬置 ③① ②① ⑤ ①① ⑦① ⑥① ⑧① ④ 序号 名称 图号 数量 扭 矩 ① 后悬置软垫总成T11-1001710BA 1 ②   ② 后悬置支架T11-1001811DA ③ 六角法兰面螺栓Q184B1295TF6 105±5N.m ④ 六角法兰面螺母Q330B12 ⑤ 六角法兰面螺栓Q184B1235TF6 ⑥ 六角法兰面螺栓Q184B1240TF6 ⑦ 六角法兰面螺母Q330C10 70±5N.m ⑧ 六角法兰面螺栓Q184B1230TF6 2 80±5N.m ③① ②① ⑤ ①① ⑦① ⑥① ⑧① ④

Rear Suspension ③① ②① ⑤ ①① ⑦① ⑥① ⑧① ④ Serial No. Name and Figure No. Quantity Torque ① Rear Mount Soft Gasket Assembly T11-1001710BA 1   ② Rear Mount Bracket T11-1001811DA ③ Hexagonal Flange Bolt Q184B1295TF6 105±5N.m ④ Hexagonal Flange nut Q330B12 ⑤ Hexagonal Flange Bolt Q184B1235TF6 ⑥ Hexagonal Flange Bolt Q184B1240TF6 ⑦ Hexagonal Flange Nut Q330C10 70±5N.m ⑧ Hexagonal Flange Bolt Q184B1230TF6 2 80±5N.m ③① ②① ⑤ ①① ⑦① ⑥① ⑧① ④

进气系统 ɑ 空气滤清器的安装： —用4个M6螺母将空气流量计安装在空气滤清器上，同时把1个引气管连接在空滤器上，螺母拧紧力矩为10±2Nm ɑ 空气滤清器的安装： —用4个M6螺母将空气流量计安装在空气滤清器上，同时把1个引气管连接在空滤器上，螺母拧紧力矩为10±2Nm —将橡胶减震圈内外涂上一般油脂或肥皂水，压入车身悬置孔内； —将空滤清器底部支撑卡涂上一般油脂或肥皂水并放在安装位置上；将空滤器谐振箱口与谐振箱进气管口对正，然后将空滤器底部支撑卡压入橡胶减震圈安装孔内，用2个M6螺栓分别把空滤器上安装孔固定在车身和谐振箱进气管固定支架上，拧紧力矩为10±2Nm —用2个M8螺栓将引气管固定在散热器孔内，同时调整另1个引气管，使之连接顺畅，拧紧力矩为10±1Nm

Air Intake System ɑ Installation of air cleaner: —Fix the airflow meter onto the air cleaner with 4 nuts (M6), and connect 1 bleed pipe to the air cleaner. The tightening torque of the nuts is 10±2Nm —Spread the inside and outside of the rubber shock-absorbing ring with ordinary grease or soapy water, and press it into the suspension hole on the car body —Spread the air cleaner bottom supporting clamp with ordinary grease or soapy water and put it on the installation position; align the opening of the air cleaner resonance box with the opening of the resonance box intake pipe, press the air cleaner bottom supporting clamp into the installation hole of the rubber shock-absorbing ring, and then fix the air cleaner onto the car body and the resonance box intake pipe mounting bracket by tightening 2 nuts (M6) through the installation holes on the air cleaner. The tightening torque is 10±2Nm —Fix the bleed pipe into the vent on the radiator with 2 nuts (M8), and adjust the other bleed pipe to ensure the smooth connection. The tightening torque is 10±1Nm

序号 零件号 零件名称 1 T11-1109110CA 空气滤清器带引气管总成 2 T11-1109200 空气滤清器支架总成 3 B11-1109163 橡胶减震圈 4 B11-1109162 橡胶圈套管 5 B11-1109161 橡胶圈 6 Q40208 大垫圈 7 Q40308 弹簧垫圈 8 Q150B0830 六角头螺栓 9 MR336481 空气流量传感器 10 Q32006 法兰面螺母 11 T11-1109210CA 进气橡胶管 12 Q676B95 蜗杆卡箍 13 Q676B83 14 T11-1014011CA 曲轴箱通风软管 15 AQ60114 卡箍 16 AQ60116

Air Strainer with Intake Pipe Assembly Serial No. Accessory No. Accessory Name 1 T11-1109110CA Air Strainer with Intake Pipe Assembly 2 T11-1109200 Air Strainer Bracket Assembly 3 B11-1109163 Rubber Damping Ring 4 B11-1109162 Rubber Ring Sleeve 5 B11-1109161 Rubber Ring 6 Q40208 Big gasket 7 Q40308 Spring Gasket 8 Q150B0830 Hexagonal Head Bolt 9 MR336481 Airflow Sensor 10 Q32006 Flange Nut 11 T11-1109210CA Air intake Rubber Pipe 12 Q676B95 Gear Clamp 13 Q676B83 14 T11-1014011CA Crankcase Ventilation Hose 15 AQ60114 Clamp 16 AQ60116

2、 发动机电喷部分 SQR7240T11T发动机电喷系统同东方之子 4G64 发动机电喷系统，请参照我部前期发放的《东方之子4G64、4G63发动机电喷部分维修手册》 。

2) Elecronic Fuel Injection part of Engine The electronic fuel injection system of the engine of SQR7240T11T is the same as the electronic fuel injection system of the engine of Eastar 4G64. Please refer to the Maintenance Manual of Electronic Fuel Injection System of Eastar 4G64 and 4G63 published by this Department.

发动机电喷控制原理图东方之子 4G64 发动机电喷系统请参见附件1。

The control principle diagram of the engine’s electronic fuel injection system is the same as that of Eastar F4A42. PLease refer to the Annex 1 hereto

三、自动变速箱部分 SQR7240T11T变速箱同东方之子 F4A42自动变速箱，请参照我部前期发放的《东方之子自动变速箱维修手册》 。

III. Automatic Transmission Part The automatic transmission of SQR7240T11T is the same as the automatic transmission of Eastar F4A42. Please refer to the Maintenance Manual of Automatic Transmission of Eastar published by this Department.

自动变速箱控制原理图同东方之子 F4A42自动变速箱系统请参见附件2。

The control principle diagram of the automatic transmission is the same as that of Eastar F4A42. PLease refer to the Annex 2 hereto.

四、电器部分 SQR7240T11T与SQR7247相比，电器部分增加了自动变速箱控制部分，其它部分同SQR7247，其它部分请参照我部前期发放的《 T11电路维修手册》 。

IV. Electrical Equipment Compared with SQR7247, the electrical equipment of SQR7240T11T is the same as that of SQR7247 except the additional control part of automatic transmission. Please refer to the Maintenance Manual of T11 Electric Circuit published by this Department.

由于增加了自动变速箱控制，公司对下列电器元件做了重新设计，增加了自动变速箱控制部分的线路。 1、前舱线束 T11-3724010TA 2、仪表板线束 T11-3724030TA 3、室内线束 T11-3724050TA 4、发动机线束 T11-3724180TA 5、前舱电器盒总成 T11-3723010BA 6、仪表电器盒总成 T11-3723060BA 7、正极线束总成　 T11-3724011TA 8、组合仪表 T11-3820010DB

Owing to the additional control part of automatic transmission, the Company re-designs the following electric components and increases the circuits of the control part of automatic transmission. 1、Engine Compartment Harness T11-3724010TA 2、Instrument Harness T11-3724030TA 3、In-door Harness T11-3724050TA 4、Engine Harness T11-3724180TA 5、Engine Compartment Electric Box Assembly T11-3723010BA 6、Instrument Electric Box Assembly T11-3723060BA 7、Anode Harness Assembly　 T11-3724011TA 8、Combination Instrument T11-3820010DB

前舱线束(2.4AT) 新增 左前转向灯 接前洗涤电机 接左前雾灯 接高音喇叭 接压缩机 接后洗涤电机 接低音喇叭 接电瓶正极保险盒 接右前轮速传感器 接动力转向开关 接右前大灯 接风扇控制器 接左前转向灯 接左前轮速传感器 接右前转向灯 接左前大灯 搭铁线2 接ABS控制器 搭铁线1 接右前转向灯 雨刮电机 接前舱电器盒 制动液位传感器 左前转向灯 接报警喇叭 搭铁线3 接仪表电器盒H 接仪表电器盒D 接ISU控制器电源 接仪表线束B 接室内线束 接仪表新线束A

Engine Compartment Harness (2.4AT) Left Front Turn Signal Lamp Increase To Front Wash Motor To Left front Fog Lamp To Althorn To Compressor To Rear Wash Motor To Buglelet To Battery Anode Fuse Block To Right Front Tachogenerator To Drive Turn Signal Switch To Right Head Lamp To Fan Control To Left Front Turn Signal Lamp To Right Front Turn Signal Lamp To Left Front Tachogenerator To Left Head Lamp To Ground Harness 2 To ABS Control To Ground Harness 1 To Right Front Turn Signal Lamp Wiper Motor To Engine Compartment Electrical Box Automatic Fluid Position Sensor Left Front Turn Signal Lamp To Annunciator To Ground Harness 3 To Instrument Electrical Box H To Instrument Electrical Box D To ISU Control Power Supply To Instrument Harness B To In-door Harness To Instrument New Harness A

1号脚：电源 2号脚： ECU控制线 3号脚：搭铁 前舱线束(2.4AT) 去除： 空调高低压开关插件 主风扇插件 增加： 风扇控制器插件(插件针脚定义如下图) 1号脚：电源 2号脚： ECU控制线 3号脚：搭铁

Engine Compartment Harness (2.4AT) On the basis of the engine compartment harness of original Tiggo, the engine compartment harness of the 2.4AT makes the following changes: Canceling： A/C High and Low Press Switch Insertion Piece Main Fan Insertion Piece Adding： Fan Control Insertion Piece (See the figure below for the definition of legs) Leg 1：Power Supply Leg 2：ECU Control Harness Leg 3：Ground

发动机线束(2.4AT) 接ECU D 接空气流量传感器 接喷嘴4 接喷嘴3 接喷嘴2 接TCU C 接TCU B 接ECU A 接TCU A 接前舱线束 接曲轴位置传感器 接分电器2 接发电机 接碳罐电磁阀 接喷嘴1 接空调压力开关 接仪表线束B 接仪表线束A 接EGR阀 接ECU C 接ECU B 接节气门位置传感器 接机油压力开关 接步进电机 接输入轴转速传感器 接水温传感器 接分电器1 凸轮轴位置传感器 输出轴速度传感器 接暴震传感器 接地 接选档开关 接马达 水温传感器 接前氧 接控制电磁阀

Engine Harness (2.4AT) To ECU D To Airflow Sensor To Injection Nozzle 4 To Injection Nozzle 3 To Injection Nozzle 2 To TCU C To TCU B To ECU A To TCU A To Engine Compartment Harness To Crankshaft Position Sensor To Distributor 2 To Generator To Carbon Canister solenoid valve To Injection Nozzle 1 To A/C Press Switch To Instrument Harness B To Instrument Harness A To EGR Valve To ECU C To ECU B To Throttle Position Sensor To Engine Oil Pressure Switch To Step Motor To Input Shaft Speed Sensor To Water Temperature Sensor To Distributor 1 Camshaft Position Sensor Output Shaft Speed Sensor To Knock Sensor To Earth To Selector Switch To Motor Water Temperature Sensor To Front Oxygen Sensor To Control Solenoid Valve

在原瑞虎发动机线束的基础上 ，2.4AT车型的发动机线束产生以下变化： 去除： 倒车灯开关插件 进气温度压力传感器插件 车速传感器插件 增加： 凸轮轴位置传感器插件 空气流量传感器 仪表水温传感器插件 EGR阀插件 自动变速箱系统插件

the 2.4AT makes the following changes: Canceling: Engine Harness (2.4AT) On the basis of the engine harness of original Tiggo, the engine harness of the 2.4AT makes the following changes: Canceling: Backup Lamp Switch Insertion Piece Air Intake Temperature Pressure Sensor Insertion Piece Speed Sensor Insertion Piece Adding: Camshaft Position Sensor Insertion Piece Airflow Sensor Instrument Water Temperature Sensor Insertion Piece EGR Valve Insertion Piece Automatic Transmission System Insertion Piece

1、搭铁 2、到ECU 3、电源 1、ECU电源 2、ECU 85 3、ECU 90 4、电源 5、搭铁 6、ECU 72 7、ECU 19 凸轮轴位置传感器插件： 1、搭铁 2、到ECU 3、电源 空气流量传感器插件： 1、ECU电源 2、ECU 85 3、ECU 90 4、电源 5、搭铁 6、ECU 72 7、ECU 19

1、Ground 2、To ECU 3、Power Supply 1、ECU Power Supply 2、ECU 85 3、ECU 90 Camshaft Position Sensor Insertion Piece: 1、Ground 2、To ECU 3、Power Supply Airflow Sensor Insertion Piece: 1、ECU Power Supply 2、ECU 85 3、ECU 90 4、Power Supply 5、Ground 6、ECU 72 7、ECU 19

仪表水温传感器插件: 作用： 直接将发动机水温信号送到组合仪表。 EGR阀插件: 1、电源 2、ECU 6号脚

Instrument Water Temperature Sensor Insertion Piece: Function: Directly transmitting the water-temperature signal of the engine to the combination instrument. EGR Valve Insertion Piece: 1、Power Supply 2、 ECU Leg 6

此部分线路控制原理请参照东方之子2.4AT自动变速箱。 自动变速箱系统: 包括： 输出轴速度传感器 输入轴速度传感器 控制电磁阀插件 换档开关插件 此部分线路控制原理请参照东方之子2.4AT自动变速箱。

Please refer to the automatic transmission of Eastar Automatic Transmission System: Including: Output Shaft Speed Sensor Input Shaft Speed Sensor Control Solenoid Valve Insertion Piece Selector Switch Insertion Piece Please refer to the automatic transmission of Eastar 2.4AT for the control principle of the circuit of this part.

在原瑞虎发动机线束的基础上 ，2.4AT车型的室内线束产生以下变化： 去除： 加速度传感器插件 增加： 换档开关插件 此插件位于换档杆下方，将换档杆位置 信号提供给组合仪表，并将手动加、减 档信号提供给TCU。原理与东方之子 2.4AT相同。

In-door Harness 2.4AT On the basis of the engine harness of original Tiggo, the in-door harness of the 2.4AT makes the following changes: Canceling: Acceleration Sensor Insertion Piece Adding: Gear Shift Switch Insertion Piece This insertion piece, equipped under the shift level, transmits the signal of the position of the shaft level to the combination instrument, and transmits the gear-shifting signal of to TCU. The principle is the same as that of Eastar 2.4AT.

前舱电器盒总成 注：红色圈出部分为新增或更改

Note: Parts in the red circles are added or changed. Engine Compartment Electric Box Assembly D power supply C earth terminal---to black wire E power supply B earth terminal---to red wire Note: Parts in the red circles are added or changed.

Tardiness Fuse Tardiness Fuse Tardiness Fuse Left Front High Beam Oil Pump Standby compressor fan generator Ignition Coil Manual Gear Shift Switch Blower Standby F7 Blower Relay Tardiness Fuse Standby F8 (Tardiness Fuse) Fan Control Right Front High Beam Left Front High Beam Right Front High Beam Left Clearance Lamp Right Clearance Lamp Brake Lamp Actuator Relay 30A (Tardiness Fuse) Main Relay Plucking Device 30A (Tardiness Fuse) Actuator Blower Relay Oil Pump Relay Rear Fog Light Front Fog Light Actuator Relay Standby Relay Rear Fog Light Relay Front Fog Light Relay High Beam Relay Low Beam Relay Standby Relay

仪表电器盒总成 注：红色圈出部分为新增或更改

Note: Parts in the red circles are added or changed Instrument Electric Box Assembly Note: Parts in the red circles are added or changed

Plucking Device Standby Standby Standby Standby Standby Standby Standby Compressor Relay （Tardiness Fuse） Night Light Adjuster Compressor Rear Wiper Blade Front Wiper Blade Sunroof Standby Relay （Tardiness Fuse） Key Switch Relay Coil Door Lamp, Ceiling Lamp Etc Air Bag Switch Buglelet Relay Standby Power Supply Audio Equipment Control Sunroof Switch Cigarette Lighter rear reflector adjustment switch Combination Instrument Clearance Relay Blower 4 Position Relay Buglelet Inside and Outside Recycling Seat Heat Audio Equipment Standby Relay Standby Relay anti-theft indicator、 A/C relay Whole Body Diagnosis Control Power Supply Combination Instrument Rearview Mirror Heat

五、底盘部分 SQR7240T11T与SQR7247相比，底盘部分相同，请参照我部前期发放的《 T11底盘部分维修手册》 。

V. Chassis Part The chassis part of SQR7240T11T is the same as that of SQR7247. Please refer to the Maintenance Manual of T11 Chassis Part published by this Department.

六、车身附件及车身尺寸部分 SQR7240T11T与SQR7247相比，车身附件及车身尺寸部分相同，请参照我部前期发放的《 T11车身尺寸与附件部分维修手册》 。

VI. Body Accessory and Body Dimension Part The body accessory and body dimension part of SQR7240T11T are the same as those of SQR7247. Please refer to the Maintenance Manual of T11 Body Accessory and Body Dimension Part published by this Department